4.1-rc1+ lcd fail to start: различия между версиями
Перейти к навигации
Перейти к поиску
Zombah (обсуждение | вклад) м (→Kernel 4.5-rc+: break lines) |
Zombah (обсуждение | вклад) м (add tagr recomendations) |
||
| Строка 33: | Строка 33: | ||
[ 8.079160] [drm] Initialized tegra 0.0.0 20120330 on minor 0 | [ 8.079160] [drm] Initialized tegra 0.0.0 20120330 on minor 0 | ||
[ 8.084942] initcall deferred_probe_initcall+0x0/0x88 returned 0 after 126122 usecs | [ 8.084942] initcall deferred_probe_initcall+0x0/0x88 returned 0 after 126122 usecs | ||
</pre> | |||
<pre> | |||
<tagr_> zombah: I suspect power sequencing | |||
<tagr_> zombah: you might want to try with adding some post-ramp-delays to various regulators, perhaps the panel needs some time to start up, or the regulators need time to reach the voltage | |||
<tagr_> zombah: you could possibly achieve the same effect by adding msleep() at various points in the panel driver | |||
<tagr_> zombah: such as at the beginning of ->prepare() and ->enable() | |||
</pre> | </pre> | ||
Версия от 10:13, 10 марта 2016
Kernel 4.5-rc+
Kernel compiled with tegra_defconfig, added dummy vbus regulators to usb-phy.
Panel starts fine: http://pastebin.com/en7pauJU
Panel failed to start: http://pastebin.com/5FjsBizU
DRM defered probe initcall compare:
fine: [ 6.803695] calling deferred_probe_initcall+0x0/0x88 @ 1 [ 6.814731] tegra-dc 54200000.dc: failed to probe RGB output: -517 [ 6.820254] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 6.820256] [drm] No driver support for vblank timestamp query. [ 7.396049] mmcblk0: p1 [ 7.406688] mmc1: new high speed MMC card at address 0001 [ 7.407711] mmcblk1: mmc1:0001 SEM08G 7.40 GiB [ 7.408165] mmcblk1boot0: mmc1:0001 SEM08G partition 1 1.00 MiB [ 7.408615] mmcblk1boot1: mmc1:0001 SEM08G partition 2 1.00 MiB [ 7.416898] mmcblk1: p1 p2 p3 p4 p5 p6 p7 p8 [ 7.444594] Console: switching to colour frame buffer device 128x37 [ 7.485416] drm drm: fb0: frame buffer device [ 7.519146] [drm] Initialized tegra 0.0.0 20120330 on minor 0 [ 7.524930] initcall deferred_probe_initcall+0x0/0x88 returned 0 after 704314 usecs failed: [ 7.950095] calling deferred_probe_initcall+0x0/0x88 @ 1 [ 7.957206] tegra-dc 54200000.dc: failed to probe RGB output: -517 [ 7.969720] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 7.976622] [drm] No driver support for vblank timestamp query. [ 7.997470] input: ImPS/2 Generic Wheel Mouse as /devices/serio0/input/input4 [ 8.034635] Console: switching to colour frame buffer device 128x37 [ 8.054130] drm drm: fb0: frame buffer device [ 8.079160] [drm] Initialized tegra 0.0.0 20120330 on minor 0 [ 8.084942] initcall deferred_probe_initcall+0x0/0x88 returned 0 after 126122 usecs
<tagr_> zombah: I suspect power sequencing <tagr_> zombah: you might want to try with adding some post-ramp-delays to various regulators, perhaps the panel needs some time to start up, or the regulators need time to reach the voltage <tagr_> zombah: you could possibly achieve the same effect by adding msleep() at various points in the panel driver <tagr_> zombah: such as at the beginning of ->prepare() and ->enable()